Did you know?

The Litter-Robot four-part system (base, globe, bonnet, and drawer) was constructed with easy maintenance in mind. The modular design allows for effortless access for deep cleaning and parts replacement, making it simpler for you to service your LItter-Robot. Get Litter-Robot 4 support or Litter-Robot 3 support. Litter-Robot repairMy litter robot is stuck on flashing red (1 per second). I know it’s to do with the cat sensor saying there is too much weight. How do I fix it. The robot is on flat surface, not over full and clean. I have continuous problems with the unit. It is only 2.5 years old and already have had to change the tray sensor three times. I have tried to re set it but the light continues and it just won ...The Litter-Robot is equipped with an Anti-Pinch safety feature to make the Litter-Robot extra safe for your cat. While cycling, if a potential pinch condition is detected, the globe will stop and reverse direction for 2 seconds. The yellow light will begin flashing quickly, about four times per second. You will also receive a notification on ...

The Litter-Robot 3 internal shield is a possible cause for the "3 lights flashing" fault. We strongly recommend removing the internal shield from your unit and installing a replacement key and plug. Grey and beige plug included Installation required The store will not work correctly in the case when cookies are disabled. ...I recently acquired a Litter Robot for $50, the story from the man selling it was "I buy storage lockers that people default on, and it was in a locker. Don't have a power cord to test it, so the first $50 takes it". ... The LR should have gone to a red flashing light, but a solid yellow light instead indicates serial data interference.Discover how to troubleshoot issues related to the bonnet removal on your Litter-Robot 3. Learn about yellow flashing lights, the wire harness, the night light, and more. ... breaking the bonnet connection and causing the yellow flashing light. With the robot fully assembled and at the Home position, inspect the rear of the globe and ensure ...How to clean Litter-Robot. With an automatic litter box like Litter-Robot, y ou don't have to scoop daily (or ever!). You may only have to replace your litter monthly because the patented sifting process removes only the clumps, preserving the clean litter. However, you'll still want to clean the Litter-Robot's globe every 1-3 months.

Submit support request. Select a category for your ticket. Select a sub-category for your ticket. Please describe your issue. Litter-Robot. Litter-Robot 4. Got questions or issues? Contact Litter-Robot Support today. We’re dedicated to ensuring a …Press cycle. When the cycle ends, all three lights will flash on the control panel. Next, unplug the robot from the back of the base (not the wall) while it is powered on. …Got a litter robot about 2 months ago, not had any issues with it so far. This week it's started to not recognise when there is a cat in there (timing light not flashing red for example) and we have to manually press the cycle button. Any ideas why this might be happening. I've already pressed the reset button and turned it off/on at wall ... ….

Reader Q&A - also see RECOMMENDED ARTICLES & FAQs. Litter robot 3 timing light red. Possible cause: Not clear litter robot 3 timing light red.

Simply empty the waste drawer when full! Thanks to the patented litter sifting process, litter stays clean for longer, allowing for litter savings of up to 50%. Litter-Robot 3 Connect comes equipped with connectivity features, allowing you to monitor your cat's activity using the Whisker app. Control the litter cleaning frequency and access ...Using a 3mm hex wrench, tighten the set screw by turning it to the right. Attempt to move the gear with your fingers to assess if the screw is tightened enough. If the gear still moves, repeat step 5. Remove the bonnet if needed, then replace the globe and bonnet back on the base. At the back of the globe, turn the black key into the key pocket.

Your Litter-Robot comes fully assembled and ready to use. Get started by following the steps below. If possible, place Litter-Robot in the same location as the old litter box (at least during transition). Make sure the unit is on a firm, level surface in a cool, dry location. Locate the unit near a power outlet.Perform a hard reset of your Litter-Robot. Unplug the power inlet from the back of the unit for at least 1 minute. Plug the unit back in and allow it to cycle fully. Once the unit has reached a solid blue light ready status, open the app. Begin onboarding as usual. Successful: If your unit is displaying a solid blue light, you've been successful.

2401 ferguson ln austin tx 78754 Hi! I require your help regarding a problem I'm encountering. **Light keeps changing red, yellow, blue. Tried to reset it , switch off and on and the issue remains. I have a litter robot3 open air (refurbished) Thank you so much in advance for your help! ... Litter-Robot 3 Open Air Circuit Board. Replacement Circuit Board (Without Panel) for ... prometric toledomenards distribution center plano il 60545 In this video we'll be taking a look at 5 different errors the Litter-Robot 4 may run into and how to fix them. This include LED status identification of the... Litter-Robot 3: Cycle delay setting ... Blue = 3 minutes; Yellow = 7 minutes; Red = 15 minutes ; ... The blue light will blink to confirm, then return to standby. all australium weapons Checked if the gear is loose or if it can be turned by hand (is tight and cant be turned by hand). Its used by 2 kittens which are too light for the sensor so i turn it on and off when they did their things usually. Its not even a month old (The machine) Hardware concerned: Litter Robot 3 Connect. Troubleshooting steps already taken: see aboveReattach the bonnet. There are four tabs total: two curved tabs in the back, two on the sides. The two curved tabs in back tuck into slots in the base. If they are sticking out, the unit will not cycle properly. You should feel a secure snap and hear a solid “click” when placed back into the slot and the bonnet should sit closer to the base. guernsey county ohio sheriff salehonda rancher plastic kitrestaurants booneville ar If your Litter-Robot 3 troubleshooting is more complex than the scenarios described above, you'll likely get lights flashing sequentially: Flashing yellow to red means the motor has detected an obstruction or jam. Turn that unit off and remove that bonnet and globe. Check to gear or motor obstruction.The red light should come on now. Allow the unit to complete the timing, cycle, and return to home position. ... The Blue Light flashing on a Litter-Robot 3 is caused by the Drawer Full Indication sensor. Since you’ve tested it and try to reset it without any success, you would need to purchase and replace the sensor. ... aba number 111900659 Litter-Robot comes equipped with a calibrated weight scale to accurately detect when your cat has entered the unit, as well as measure its weight. If the unit displays a red and green alternating light bar, the unit has lost its factory scale calibration values. hutchinson mn garage saleschopstix greenville scmarisa tansino The Litter-Robot 4 Cat Presence Sensor is a motion sensor that monitors the waste drawer. Purchase a replacement cat presence sensor, or contact Whisker Customer Experience if your Litter-Robot 4 is still under warranty. ... If you are unable to resolve the red ping-pong light bar on the control panel or the "Motion in Drawer" message in ...View the Litter-Robot 3 Waste Drawer Liner Installation Video. To change the drawer liner in Litter-Robot 4, pull out the drawer and dispose of the soiled liner. Open a new waste drawer liner and wrap the edges over the rim of the waste drawer. Push the remainder of the bag into the bottom of the waste drawer. Check out the Litter-Robot 4 Waste ...